Steinbach SPS 100-1 Self-Priming Filter Pump User Manual

1. Ynlieding

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Steinbach SPS 100-1 self-priming filter pump. Please read all instructions carefully before installation and use. Keep this manual for future reference.

2. Safety Ynstruksjes

Wichtige feiligensynformaasje:

• Always disconnect the pump from the power supply before performing any maintenance or cleaning.
• Ensure the electrical installation complies with local regulations and is protected by a Residual Current Device (RCD) with a tripping current not exceeding 30 mA.
• Do not operate the pump if the power cord or plug is damaged. Contact qualified personnel for repairs.
• The pump must be installed on a solid, level surface, protected from direct sunlight and rain.
• Ensure adequate ventilation around the pump motor to prevent overheating.
• Dit apparaat is net bedoeld foar gebrûk troch persoanen (ynklusyf bern) mei fermindere fysike, sintúchlike of mentale kapasiteiten, of gebrek oan ûnderfining en kennis, útsein as se hawwe krigen tafersjoch of ynstruksje oangeande it brûken fan it apparaat troch in persoan ferantwurdlik foar harren feiligens.
• Bern moatte tafersjoch wurde om te soargjen dat se net mei it apparaat boartsje.

3. Produkt Overview

The Steinbach SPS 100-1 is a self-priming filter pump designed for efficient water circulation in swimming pool filter systems, such as the Speed Clean Comfort 75. It operates without a built-in timer, offering continuous operation when powered.

Components

• Pump body with motor
• Pre-filter basket with transparent lid
• Inlet en outlet ferbinings
• Stromkabel mei stekker

Ofbylding 1: Oerview of the Steinbach SPS 100-1 Self-Priming Filter Pump.

figuer 2: Close-up view of the pre-filter housing and the inlet connection with a hose attached. The transparent lid allows for easy inspection of the filter basket.

figuer 3: Detailed view of the pre-filter and the threaded inlet connection, ready for hose attachment.

Figure 4: Close-up of the pump's outlet connection with a hose securely fastened, directing filtered water.

figuer 5: Detailed view of the pump's threaded outlet connection, showing the port where the return hose connects.

Figure 6: Product label displaying technical specifications such as model number, voltage, power, and flow rate.

4. Opset en ynstallaasje

Proper installation is crucial for the pump's performance and longevity. Refer to your specific filter system manual for detailed plumbing instructions.

4.1 Pleatsing

• Position the pump as close to the pool as possible, below water level if feasible, to aid in self-priming.
• Ensure the pump is on a stable, level, and dry surface.
• Protect the pump from direct weather exposure (rain, snow, direct sunlight).
• Allow sufficient space around the motor for ventilation and maintenance access.

4.2 Loodgietersferbiningen

• Connect the suction line from the pool skimmer/main drain to the pump's inlet (front connection).
• Connect the discharge line from the pump's outlet (top connection) to the filter system's inlet.
• Use appropriate fittings, clamps, and thread sealant (Teflon tape) to ensure watertight connections.
• Avoid kinks or sharp bends in hoses to maintain optimal flow.

4.3 Elektryske ferbining

• Soargje derfoar dat de stroomfoarsjenning oerienkomt mei it folume fan 'e pomptage (230 V).
• Plug the pump into a grounded electrical outlet protected by an RCD.
• Brûk gjin ferlingkabels, útsein as it absolút needsaaklik is, en soargje derfoar dat se geskikt binne foar bûtengebrûk en de stroomeasken fan 'e pomp.

5. Bedriuwsinstruksjes

5.1 Foarmje de pomp

As a self-priming pump, the SPS 100-1 can draw water, but initial priming is recommended for faster startup:

1. Ensure all valves are open, allowing water to flow from the pool to the pump.
2. Remove the transparent lid of the pre-filter.
3. Fill the pre-filter housing completely with water.
4. Replace the lid securely, ensuring the O-ring is properly seated to prevent air leaks.
5. Turn on the pump. It should begin to draw water and expel air. If it does not prime within a few minutes, turn it off, re-check connections, and repeat the priming process.

5.2 Normale operaasje

• Once primed, the pump will continuously circulate water through your filter system.
• Monitor the pressure gauge on your filter (if applicable) to determine when backwashing or filter cleaning is needed.
• This model does not include a timer, so you will need to manually switch it on and off or connect it to an external timer (not included).

6. Underhâld

6.1 Pre-Filter Basket Cleaning

Regularly inspect and clean the pre-filter basket to prevent debris buildup and maintain pump efficiency.

1. Turn off the pump and disconnect it from the power supply.
2. Slút alle nedige kleppen om te foarkommen dat wetter út it swimbad streamt.
3. Unscrew the transparent lid of the pre-filter.
4. Remove the basket and empty any collected debris.
5. Spoel de koer goed ôf mei wetter.
6. Ynspektearje de O-ring op it deksel op skea en soargje derfoar dat it skjin is.
7. Doch de koer werom en meitsje it deksel goed fêst.

6.2 Winterization

Before freezing temperatures arrive, properly winterize your pump to prevent damage:

• Skeakelje de pomp út 'e macht oanbod.
• Drain all water from the pump by removing the drain plug (usually located at the bottom of the pump housing).
• Disconnect all hoses and pipes.
• Clean the pre-filter basket and housing.
• Bewarje de pomp op in droech, froastfrij plak.

7. Probleemoplossing

8. Spesifikaasjes

9. Garânsje en stipe

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Steinbach customer service directly. Keep your proof of purchase for warranty claims.

Kontakt ynformaasje:

• Manufacturer: Steinbach
• Website: www.steinbach.at (Please check for local support details)