Braeburn 5-2 Day Programmable Thermostat

Ynlieding

This manual provides comprehensive instructions for the installation, operation, programming, and maintenance of your Braeburn 5-2 Day Programmable Thermostat. Please read this manual thoroughly before attempting to install or operate your new thermostat.

Ofbylding 1: Front view of the Braeburn 5-2 Day Programmable Thermostat, showing the large blue backlit display, system mode switch, fan mode switch, and programming buttons.

Features

• 5-2 Day Programmability
• Grutte 2 Sq. Yn. Display mei Bright Blue Backlight
• Ferstelbere temperatuergrinzen
• Hardwire or Battery Powered (24V AC)
• Permaninte ûnthâld behâldt ynstellings
• Filter Kontrolearje Monitor
• Ferstelbere temperatuerdifferinsjaal
• Adaptive Recovery Mode (ARM)
• ESD Guard Electronic Circuitry
• Compressor Koarte Syklus beskerming
• Tydlike programma oerskriuwe
• Programmierbare Extended Hold Mode
• Front Access Reset Button
• F° / C° Switch

Ynstallaasje en opset

Feiligens foarsoarchsmaatregels

• WARSKÔGING: Disconnect power to the heating and cooling system before installing or servicing the thermostat.
• Ynstallaasje moat wurde útfierd troch in kwalifisearre technikus.
• Ensure wiring complies with local electrical codes.

Montage Lokaasje

Install the thermostat on an inside wall, approximately 5 feet (1.5m) above the floor. Avoid locations near heat sources (lamps, sunlight, fireplaces), drafts (windows, doors), or unconditioned spaces (unheated hallways, outside walls).

Wiring Ynstruksjes

This thermostat is designed for single-stage (1 Heat/1 Cool) systems. It can be powered by 24V AC hardwire or batteries.

Typical Terminations: Rc, Rh, O, B, Y1, W1, G, C

1. Skeakelje de stroom nei it HVAC-systeem út by de stroomûnderbrekker.
2. Remove the old thermostat from the wall plate.
3. Label each wire with the terminal designation from your old thermostat.
4. Mount the new thermostat base plate to the wall.
5. Connect the labeled wires to the corresponding terminals on the new thermostat. Refer to the wiring diagram provided with your thermostat for specific connections.
6. Insert 2 AA alkaline batteries (not included) into the battery compartment if using battery power or as a backup.
7. Attach the thermostat body to the base plate.
8. Herstel macht oan it HVAC -systeem.

Jo thermostaat operearje

Systeem Mode Switch

Located on the front of the thermostat, this switch controls the overall operation mode:

• KOEL: De termostaat sil jo koelsysteem betsjinje.
• ÚT: De ferwaarming- en koelsystemen binne útskeakele.
• HJITTE: De termostaat sil jo ferwaarmingssysteem betsjinje.

Fan Mode Switch

Located on the front of the thermostat, this switch controls the fan operation:

• AUTO: De fentilator draait allinnich as it ferwaarmings- of koelsysteem aktyf is.
• OP: De fentilator draait kontinu, ûnôfhinklik fan ferwaarmings- of koeloproppen.

Temperatuer ynstelle

Brûk de UP en OMLEECH arrow buttons on the right side of the display to adjust the desired temperature (setpoint). The display will show both the current room temperature and the setpoint.

Programming (5-2 Day)

The 5-2 day programming allows you to set different schedules for weekdays (Monday-Friday) and weekends (Saturday-Sunday). Each day can have up to 4 program periods: Morning, Day, Evening, and Night.

Tiid en dei ynstelle

1. Druk op de PROG button once. The display will show the current time flashing.
2. Brûk de UP or OMLEECH pylken om de tiid oan te passen.
3. Parse PROG again to advance to the day setting. The day will flash.
4. Brûk de UP or OMLEECH arrows to adjust the day.
5. Parse PROG or wait 15 seconds to exit.

Setting Program Schedule

1. Druk op de PROG button until "MON-FRI" appears and the time for the first period (Morning) flashes.
2. Brûk de UP or OMLEECH arrows to set the desired time for the Morning period.
3. Parse PROG. The temperature for the Morning period will flash.
4. Brûk de UP or OMLEECH pylken om de winske temperatuer yn te stellen.
5. Repeat steps 2-4 for the Day, Evening, and Night periods for "MON-FRI".
6. After setting the "MON-FRI" schedule, press PROG to advance to "SAT-SUN" and repeat the process for weekend programming.
7. Parse WEROMKOMME or wait 15 seconds to exit programming mode.

Tydlike programma oerskriuwe

To temporarily change the temperature without affecting the program, simply use the UP or OMLEECH arrows. The thermostat will hold this temperature until the next program period begins.

Permaninte Hold

Druk op de HÂLDE button. The thermostat will maintain the current temperature indefinitely. To cancel, press HÂLDE wer of drukke PROG om it skema wer op te pakken.

Ûnderhâld

Batterij ferfanging

When the battery indicator appears on the display, replace the 2 AA alkaline batteries immediately to ensure proper operation and prevent loss of settings. The thermostat has permanent memory, so settings will be retained during battery replacement.

1. Lûk de termostaat foarsichtich fan 'e muorreplaat ôf.
2. Fuortsmite de âlde batterijen.
3. Insert new AA alkaline batteries, observing polarity (+/-).
4. Klik de termostaat werom op 'e muorreplaat.

Cleaning

Reinigje de thermostaat mei in sêft, damp doek. Brûk gjin abrasive skjinmakkers of solvents.

Filter Kontrolearje Monitor

The thermostat may feature a filter check monitor that reminds you to change your air filter. Consult your HVAC system manual for recommended filter replacement intervals.

Troubleshooting

If problems persist, contact a qualified HVAC technician or Braeburn customer support.

Spesifikaasjes

Garânsje en stipe

For warranty information and technical support, please refer to the documentation included with your product or visit the official Braeburn webside. Bewarje jo oankeapbewiis as bewiis fan oankeap.

Fabrikant: Braeburn