SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Ynlieding

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

figuer 1.1: Front view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Safety Information

• Lês alle ynstruksjes soarchfâldich foar ynstallaasje en operaasje.
• Soargje derfoar dat de macht oanbod voltage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Brûk it apparaat net yn omjouwings mei tefolle focht, stof of korrosive gassen.
• Skeakelje de stroom út foardat jo ûnderhâld of bedrading feroarje.
• Keep the device away from strong electromagnetic interference.

3. Produktfunksjes

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. Package Ynhâld

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x brûkershantlieding (dit dokumint)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Opsette

5.1 Montage

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Bedrading

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminals 1 & 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminals 3 & 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminals 6 & 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminals 11 & 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Bedriuwsinstruksjes

6.1 Display oerview

The meter features a dual display:

• PV (Proseswearde): The upper red display shows the current measured temperature/humidity.
• SV (Ynstelde wearde): The lower green display shows the desired set point.
• OUT-yndikator: Illuminates when the main output is active.
• AT-yndikator: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Knop Funksjes

• SET knop: Brûkt om de parameterynstellingsmodus yn te gean en seleksjes te befêstigjen.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. In normal operating mode, press the SET knop ien kear yndrukke. It SV-display sil begjinne te knipperjen.
2. Brûk de ▲ (Omheech) en ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Druk op de SET button again to confirm the new SV and exit the setting mode.

6.4 Avansearre parameterynstellingen

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the SET button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Omheech) en ▼ (Down) buttons to navigate through parameters and the SET button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Underhâld

• Reiniging: Wiskje it skerm ôf en casinmei in sêfte, droege doek. Brûk gjin abrasive reinigingsmiddels of oplosmiddels.
• Ynspeksje: Kontrolearje de bedrading periodyk op losheid of korrosje.
• Opslach: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Probleemoplossing

9. Spesifikaasjes

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Garânsje en stipe

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER website foar kontakt ynformaasje.