DD Audio SS6000
DD Audio SS6000 Monoblock Amplifier Instruction Manual
Ynlieding
Thank you for choosing the DD Audio SS6000 Monoblock Amplifier. Dit amplifier is designed to deliver high-performance audio for your vehicle's sound system. This manual provides essential information for the correct installation, operation, and maintenance of your SS6000 ampLifier. Lês dizze hantlieding goed troch foardat jo besykje te ynstallearjen of te brûken om optimale prestaasjes en feiligens te garandearjen.
Safety Information
Observe the following safety precautions to prevent injury and damage to the amplifter of auto:
- Meitsje altyd de negative terminal fan 'e batterij fan' e auto los foardat jo begjinne mei elektrysk wurk.
- Soargje foar goede grûn fan 'e amplifter nei it chassis fan 'e auto.
- Brûk passende trieddiktes foar stroom-, ierd- en sprekkerferbiningen lykas oanjûn yn dizze hantlieding.
- Ynstallearje de amplifier in a dry, well-ventilated location, away from direct sunlight, heat sources, and moisture.
- Mije mounting de amplifier in areas where it could interfere with vehicle operation or safety systems.
- Net besykje te iepenjen of wizigjen de ampLifier. Lit alle ûnderhâldswurk oer oan kwalifisearre personiel.
- Beskermje alle bedrading tsjin skerpe rânen en bewegende ûnderdielen.
Pakketynhâld
Kontrolearje oft alle items yn it pakket oanwêzich binne:
- DD Audio SS6000 Monoblock Amplibbener
- Remote Gain Control Unit
- Montagehardware (skroeven, ensfh.)
- Ynstruksjehânlieding (dit dokumint)
Image: The remote gain control unit, featuring a voltage display, power indicator, clip indicator, and a rotary knob for gain adjustment.
Opset en ynstallaasje
1. Mounting Lokaasje
Choose a mounting location that is secure, dry, and provides adequate ventilation for the amplifier. Avoid mounting on carpet or in enclosed spaces without airflow. Ensure the amplifier is accessible for wiring and adjustments.
2. Wiring Ferbinings
Proper wiring is crucial for performance and safety. Refer to the diagram below for connection points.
Ofbylding: Boppe en ûnder views of the DD Audio SS6000 amplifier. The top view shows dual 0 AWG power and ground terminals. The bottom view displays RCA inputs, gain and filter controls (SENS, SUB SONIC, LPF), a remote port, and speaker output terminals.
- Krêft (BATT+): Connect a 0 AWG power cable directly from the positive terminal of the vehicle's battery to the +12V terminals on the amplifier. Install an appropriate fuse (600A recommended) within 18 inches of the battery. The SS6000 features dual 0 AWG power terminals for robust current delivery.
- Grûn (GND): Connect a 0 AWG ground cable from the GND terminals on the amplifier to a clean, unpainted metal surface of the vehicle chassis. The ground point should be as short as possible and securely fastened. The SS6000 features dual 0 AWG ground terminals.
- Op ôfstân (REM): Connect a 18 AWG or larger wire from the vehicle's head unit remote output to the REM terminal on the amplifter. Dizze tried draait de amplifer oan en út mei de haadunit.
- RCA Input (INPUT L/R): Ferbine RCA-kabels fan 'e foarfersterker fan jo haadienheidamp outputs to the RCA INPUTs on the amplibbener.
- Speaker Output (SPEAKER): Connect your subwoofer speaker wires (4 AWG recommended) to the SPEAKER terminals. Ensure correct polarity (+ to + and - to -). The SS6000 is a monoblock amplifier designed for a single channel output.
- Remote Gain Control: Connect the included remote gain control unit to the "REMOTE" port on the amplifier mei de levere kabel.
Operating Instructions
1. Inisjele ynskeakeljen en fersterkingsynstelling
After all connections are made, reconnect the vehicle's battery. Turn on your head unit. The amplifier should power on (PWR indicator will illuminate). Begin with the amplifier's SENS (gain) control set to minimum (fully counter-clockwise) and the head unit volume at a low level.
- Play a familiar audio track.
- Increase the head unit volume to about 75-80% of its maximum.
- Slowly increase the SENS (gain) control on the amplifier until you hear distortion or the CLIP indicator on the remote gain control unit illuminates. Then, back off the gain slightly until the distortion disappears or the CLIP indicator turns off.
- The remote gain control unit allows for convenient adjustment of the ampit útfiernivo fan 'e lifter fan 'e bestjoerdersstoel.
2. Filter Adjustments
The SS6000 features adjustable filters to optimize sound quality for your subwoofer system:
- SUB SONIC (High Pass Filter): This filter removes extremely low frequencies that are inaudible or harmful to subwoofers. Adjust between 20Hz and 80Hz. A common setting is around 25-30Hz, depending on your subwoofer's capabilities and enclosure tuning.
- LPF (Low Pass Filter): This filter allows only frequencies below the set point to pass to the subwoofer, preventing it from playing higher frequencies meant for full-range speakers. Adjust between 80Hz and 20kHz. Typically, for subwoofers, this is set between 80Hz and 120Hz, depending on the crossover point of your main speakers.
Ûnderhâld
The DD Audio SS6000 amplifier requires minimal maintenance. Keep the amplifier clean and free of dust and debris. Periodically check all wiring connections for tightness and corrosion. Ensure that the amplifier's cooling fins are not obstructed to maintain proper heat dissipation.
Troubleshooting
As jo ûnderfine problemen mei dyn amplifier, consult the table below for common problems and solutions before contacting support.
| Probleem | Mooglike oarsaak | Oplossing |
|---|---|---|
| Amplifier does not turn on (no PWR light) | No power, no ground, or no remote signal. Blown fuse. | Check battery connections, ground connection, and remote wire. Verify fuse at battery is intact. |
| Gjin lûdútfier | RCA cables disconnected, speaker wires disconnected, gain too low, head unit muted. | Check RCA and speaker connections. Adjust gain. Ensure head unit is playing audio. |
| Ferfoarme lûd | Gain set too high, improper filter settings, poor quality audio source. | Reduce gain. Adjust SUB SONIC and LPF settings. Use a high-quality audio source. |
| Amplifier goes into protect mode (PRO light on) | Overheating, short circuit in speaker wiring, impedance too low. | Ensure proper ventilation. Check speaker wiring for shorts. Verify speaker impedance is within amplifier's rated limits (1 Ohm minimum). |
| Noise (hissing, whining) | Ground loop, poor RCA shielding, power wire too close to signal wires. | Ensure good ground connection. Reroute RCA cables away from power wires. Consider a ground loop isolator if necessary. |
Spesifikaasjes
The following are the technical specifications for the DD Audio SS6000 Monoblock Amplibbener:
| Eigenskip | Spesifikaasje |
|---|---|
| Model | SS6000 |
| Operaasje Voltage | 9 - 16 Volt |
| Test Voltage | 14.4 Volt |
| Utfierkanalen | 1 (Monoblok) |
| Trochrinnende Wattage @4 omt | 2000 Watt RMS |
| Trochrinnende Wattage @2 omt | 4000 Watt RMS |
| Trochrinnende Wattage @1 omt | 6000 Watt RMS |
| Max Aktuele Draw | 600 Amps |
| RCA Input Voltage Sensitiviteit | 0.4 - 4 Volt |
| Signal-to-Noise Ratio (S/N) | >95 dB |
| Dampyn Faktor | >100 |
| Totale Harmonyske ferfoarming (THD) | <1.0% |
| Frequency Response | 20 - 20,000 Hz |
| Sub-Sonic Filter (HPF) | 20 - 80 Hz (12dB/Oct) |
| Low-Pass Filter (LPF) | 80 - 20,000 Hz (12dB/Oct) |
| Power Wire Gauge | 0 AWG (Dual Terminals) |
| Speaker Wire Gauge | 4 AWG |
| Ofmjittings (L x B x H) | 11.25 x 7.3 x 2.4 inch (286 x 185 x 60 mm) |
| Item Gewicht | 11 pyk |
Garânsje en stipe
For warranty information, please refer to the documentation provided with your purchase or visit the official DD Audio website. If you encounter issues not covered in the troubleshooting section, or require further assistance, please contact DD Audio customer support or your authorized dealer. Do not attempt to repair the amplifier yourself, as this may void your warranty.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.